Bulk stellar properties
Stellar temperatures
Temperatures of stars can be defined in a number of ways. From the character of the spectrum and the various degrees of ionization and excitation found from its analysis, an ionization or excitation temperature can be determined.
A comparison of the V and B magnitudes (see above Stellar colours) yields a B − V colour index, which is related to the colour temperature of the star. The colour temperature is therefore a measure of the relative amounts of radiation in two more or less broad wavelength regions, while the ionization and excitation temperatures pertain to the temperatures of strata wherein spectral lines are formed.
Provided that the angular size of a star can be measured (see below Stellar radii) and that the total energy flux received at Earth (corrected for atmospheric extinction) is known, the so-called brightness temperature can be found.
The effective temperature, Teff, of a star is defined in terms of its total energy output and radius. Thus, since σT4eff is the rate of radiation per unit area for a perfectly radiating sphere and if L is the total radiation (i.e., luminosity) of a star considered to be a sphere of radius R, such a sphere (called a blackbody) would emit a total amount of energy equal to its surface area, 4πR2, multiplied by its energy per unit area. In symbols, L = 4πR2σT4eff. This relation defines the star’s equivalent blackbody, or effective, temperature.
Since the total energy radiated by a star cannot be directly observed (except in the case of the Sun), the effective temperature is a derived quantity rather than an observed one. Yet, theoretically, it is the fundamental temperature. If the bolometric corrections are known, the effective temperature can be found for any star whose absolute visual magnitude and radius are known. Effective temperatures are closely related to spectral type and range from about 40,000 K for hot O-type stars, through 5,800 K for stars like the Sun, to about 300 K for brown dwarfs.
Stellar masses
Masses of stars can be found directly only from binary systems and only if the scale of the orbits of the stars around each other is known. Binary stars are divided into three categories, depending on the mode of observation employed: visual binaries, spectroscopic binaries, and eclipsing binaries.
Visual binaries
Visual binaries can be seen as double stars with the telescope. True doubles, as distinguished from apparent doubles caused by line-of-sight effects, move through space together and display a common space motion. Sometimes a common orbital motion can be measured as well. Provided that the distance to the binary is known, such systems permit a determination of stellar masses, m1 and m2, of the two members. The angular radius, a″, of the orbit (more accurately, its semimajor axis) can be measured directly, and, with the distance known, the true dimensions of the semimajor axis, a, can be found. If a is expressed in astronomical units, which is given by a (measured in seconds of arc) multiplied by the distance in parsecs, and the period, P, also measured directly, is expressed in years, then the sum of the masses of the two orbiting stars can be found from an application of Kepler’s third law. (An astronomical unit is the average distance from Earth to the Sun, 149,597,870.7 km [92,955,807.3 miles].) In symbols, (m1 + m2) = a3/P2 in units of the Sun’s mass. For example, for the binary system 70 Ophiuchi, P is 87.8 years, and the distance is 5.0 parsecs; thus, a is 22.8 astronomical units, and m1 + m2 = 1.56 solar masses. From a measurement of the motions of the two members relative to the background stars, the orbit of each star has been determined with respect to their common centre of gravity. The mass ratio, m2/(m1 + m2), is 0.42; the individual masses for m1 and m2, respectively, are then 0.90 and 0.66 solar mass.
The star known as 61 Cygni was the first whose distance was measured (via parallax by the German astronomer Friedrich W. Bessel in the mid-19th century). Visually, 61 Cygni is a double star separated by 83.2 astronomical units. Its members move around one another with a period of 653 years. It was among the first stellar systems thought to contain a potential planet, although this has not been confirmed and is now considered unlikely. Nevertheless, since the 1990s a variety of discovery techniques have confirmed the existence of thousands of planets orbiting other stars (see below Binaries and extrasolar planetary systems).
Spectroscopic binaries
Spectroscopic binary stars are found from observations of radial velocity. At least the brighter member of such a binary can be seen to have a continuously changing periodic velocity that alters the wavelengths of its spectral lines in a rhythmic way; the velocity curve repeats itself exactly from one cycle to the next, and the motion can be interpreted as orbital motion. In some cases, rhythmic changes in the lines of both members can be measured. Unlike visual binaries, the semimajor axes or the individual masses cannot be found for most spectroscopic binaries, since the angle between the orbit plane and the plane of the sky cannot be determined. If spectra from both members are observed, mass ratios can be found. If one spectrum alone is observed, only a quantity called the mass function can be derived, from which is calculated a lower limit to the stellar masses. If a spectroscopic binary is also observed to be an eclipsing system, the inclination of the orbit and often the values of the individual masses can be ascertained.